| G101/G102 C101/C102 |
|
| PICK THE CORRECT SERIES |
|
| NO. |
DESCRIPTION |
GENERAL NO. |
| Not Shown |
ONLY HEX NUT |
391-1451-076 |
| 2 |
ONLY WASHER |
391-3784-028 |
| 3 |
101 BRACKET OPTIONAL |
314-0100-005 |
| 4 |
101 SNAP RING |
391-2681-493 |
| 5 |
101 LUIP SEAL |
391-2883-096 |
| 6 |
101 SHAFT END COVER |
314-5039-201 |
| 7 |
RING SEAL |
391-2585-009 |
| 8 |
ROLLER BRG. |
391-0381-059 |
| 9 |
THRUST PLATE |
391-2185-012 |
| Not Shown |
POCKET SEAL |
391-2882-050 |
| 11 |
101 SHAFT & GEAR SET |
314-29XX-640 |
| 12 |
GEAR HOUSING GASKET |
391-2884-021 |
| 13 |
GEAR HOUSING |
314-80XX-100 |
| 14a |
101 PORT END COVER |
314-3910-903 |
| 14b |
102 PORT END COVER |
314-3910-904 |
| 15 |
SPOOL VALVE |
314-4000-001 |
| 16 |
QUAD RING |
391-2881-103 |
| 17 |
WIPER RING |
391-2883-147 |
| 18 |
C ONLY RETAINER RING |
391-3782-126 |
| 19 |
C ONLY SNAP RING |
391-2688-003 |
| 20 |
DETENT CAP |
314-0100-003 |
| 21 |
DETENT BALL |
391-0282-009 |
| 22 |
DETENT SPRING |
391-3581-383 |
| 23 |
LOCK WASHER |
391-3788-002 |
| 24 |
DETENT RETAINER |
391-2583-079 |
| 25 |
RELIEF VALVE |
355-9001-067 |
| 26 |
WASHER |
391-3784-029 |
| 27a |
CAP SCREW / MH101-20 |
391-1401-111 |
| 27b |
CAP SCREW / MH101-25 |
391-1401-110 |
| 28a |
CAP SCREW / MH102 -20 |
391-1425-433 |
| 28b |
CAP SCREW / MH102 -25 |
391-1425-432 |
| 29 |
OPTIONAL SLEEVE |
391-3283-052 |
| 30 |
PIPE PLUG |
391-2282-006 |
| 31 |
SPOOL END CAP |
391-1881-073 |
| 32 |
SPIRAL PIN |
391-2085-009 |
| 33 |
BRACKET |
391-0981-010 |
| 34 |
S.H.C.SCREW |
391-1402-063 |
| Not Shown |
102 SNAP RING |
391-2686-065 |
| Not Shown |
102 SEAL RETAINER |
391-3383-087 |
| 36 |
102 SPACER |
N/A |
| 37 |
102 LIP SEAL |
391-2883-115 |
| 38 |
102 SHAFT END COVER |
313-5037-201 |
| 39 |
CHECK VALVES |
391-3681-001 |
| 40 |
MH 102 SHAFT & GEAR SET 7/8" x 13 tooth spline |
314-29XX-130 |
| 41a |
CAP SCREW 1 MH101-102 |
391-1401-082 |
| Not Shown |
SHAFT KEY |
391-1781-021 |
| Not Shown |
SEAL RETAINER |
N/A |
| |
|
|
| P30/P31 |
|
| NO. |
DESCRIPTION |
GENERAL NO. |
| 1 |
SHAFT BEARING SN P RING |
391-2686-063 |
| 2a |
INPUT SHAFT BEARING |
391-0381-040 |
| 2b |
BEARING SPACER ( IN PLACE OF SHAFT BEARING) |
391-3383-068 |
| 3 |
MOTOR SEAL RETAINER USED WITH SHAFT BEARING OR SPACER |
391-3381-040 |
| 4a |
PUMPLIP SEAL FOR CONTINENTAL SHAFT ONLY |
391-2883-107 |
| 4b |
PUMP LIP SEAL FOR PIGGY BACK 76/31 SHAFT END COVER |
391-2883-103 |
| 4c |
MOTOR UIP SEAL |
391-2883-119 |
| 4d |
MOTOR UIP SEAL FOR CONTINENTAL SHAFT ONLY |
391-2883-126 |
| 5a |
31 PAD PILOT PUMP S.E.C. TYPE 00 |
312-5017-201 |
| 5b |
31 6 BOLT ROUND WITH 2.625* or 66,67 mm PILOT PUMP S.E.C. TYPE 05 |
312-5047-201 |
| 5c |
31 4 BOLTB PILOT PUMP S.E.C. TYPE 42 (4" or 101,6 mm pilot) |
312-5037-201 |
| 5d |
31 4 BOLT CPILOT PUMP S.E.C. TYPE 78 (5" or 127 mm pilot) |
312-5037-202 |
| 5e |
31 2 BOLTAPILOT PUMP S.E.C. TYPE 94 (3 1/4" or 82.55 mm pilot) |
312-5027-204 |
| 5f |
31 2 BOLTB PILOT PUMP S.E.C. TYPE 97 (4" or 101,6 mm pilot) |
312-5027-201 |
| 5g |
31 2 BOLT B (TYPE2) PILOT PUMP S.E.C. TYPE 96 (4" or 101,6 mm pilot) |
312-5027-205 |
| 5h |
[ 31/51 SHAFT END COVER FOR PIGGYBACK UNITS TYPE 91 |
312-5027-208 |
| 5i |
76/31 SHAFT END COVER FOR PIGGYBACK UNITS TYPE 92 |
312-5027-209 |
| 5j |
31 2/4 BOLTB PILOT PUMP S.E.C. TYPE 46 (4" or 101.6 mm pilot) |
312-5053-202 |
| 5k |
31 PAD PILOT MOTOR S.E.C. TYPE 00 |
312-5017-401 |
| 5L |
31 6 BOLT ROUND WITH 2.625"or 66,67 mm PILOT MOTOR S.E.C. TYPE 05 |
312-5047-401 |
| 5m |
31 4 BOLTB PILOT MOTOR S.E.C. TYPE 42 (4" or 101,6 mm pilot) |
312-5037-401 |
| 5n |
31 4 BOLT C PILOT MOTOR S.E.C. TYPE 78 (5 or 127 mm pilot) |
312-5037-402 |
| 5o |
31 2 BOLT A PIL OT MOTOR S.E.C. TYPE 94 (3 14 or 82,55 mm pilot) |
312-5027-404 |
| 5p |
31 2 BOLT B PILOT MOTOR S.E.C. TYPE 97 (4" or 101,6 mm pilot) |
312-5027-401 |
| 5q |
31 2/4 BOLTB PILOT MOTOR S.E.C. TYPE 46 (4" or 101,6 mm pilot) |
312-5053-402 |
| |
FOR MORE INFORMATION OR SPECIAL ORDER,PLEASE CONTACT US |
GENERAL NO. |
| 6a |
CHECK VALVE MOTOR |
391-3681-001 |
| 6b |
PRESSURE PLUG PUMP |
391-2286-004 |
| 7 |
RING SEAL |
391-2585-006 |
| 8 |
ROLLER BEARING (∅1.687" O.D.) |
391-0381-068 |
| 9a |
PUMP THRUST PLATE |
391-2185-031 |
| 9b |
MOTOR THRUSTPL ATE |
391-2185-013 |
| 10 |
POCKET SEAL |
391-2882-086 |
| 11a |
SHAFT & GEAR TYPE 30 (0.875" ∅ x 1/4" x3/B" x 1" key) |
312-29XX-730 |
| 11b |
SHAFT & GEAR TYPE 25( 0.875" ∅- 13-ooth splin) |
312-29XX-230 |
| 11c |
SHAFT & GEAR TYPE 43 (1.00" ∅x 14" x 14" x11/4" key) |
312-29XX-740 |
| 11d |
SHAFT & GEAR TYPE 65 TYPE 2( 0.875" ∅- 13-Tooth spline) |
312-29XX-430 |
| 11e |
SHAFT & GEAR TYPE 65 TYPE 98(1"∅ - 15-Tooth splin) |
312-29XX-240 |
| 12 |
PUMP & MOTOR HOUSING GASKET |
391-2884-050 |
| 13 |
PUMP & MOTOR GEAR HOUSING |
312-82XX-100 |
| 14a |
31 MOTOR BEARING CARRIER BLANK |
312-7740-100 |
| 14b |
31 PUMP BEARING CARRIER WITH COMMON PASSAGE |
312-7723-100 |
| 15 |
CONNECTING SHAFT |
312-1133-001 |
| 16 |
GEAR SET ONLY |
312-28XX-000 |
| 17 |
GEAR HOUSING DOWEL PIN |
391-2082-032 |
| 18a |
31 PUMP & MOTOR PORT END COVER |
312-3120-100 |
| 18b |
31 PUMP & MOTOR PORT END COVER LARGER PORTING |
312-3420-100 |
| 18c |
31/31 PIGGY BACK PORT END COVER |
312-5027-212 |
| 19 |
FLAT WASHER |
391-3784-028 |
| 20 |
BOLTS/ STUDS (5/8" UNC) |
|
| 21 |
HEX NUT (5/8 UNC) |
391-1451-076 |
| 22a |
CONTINENTAL SHAFT TYPE 30 (0.875"∅x14" x 3/8" x 1"key) |
312-1500-300 |
| 22b |
CONTINENTAL SHAFT TYPE 7 (1.250" ∅- 14-tooth splne, Continental only) |
312-1135-133 |
| 22c |
CONTINENTAL SHAFT TYPE 25 ( 0,875" ∅- 13-Tooth spline) |
312-1135-138 |
| 22d |
CONTINENTAL SHAFT TYPE43 (1.00" ∅x14" x 3/8" x1 14" key) |
312-1500-400 |
| 22e |
CONTINENTAL SHAFT TYPE 12 (0. 750" ∅x 3/16" x 3/16" 19/16- key) |
312-1135-152 |
| 221 |
CONTINENTAL SHAFT TYPE 95 (0. 625" ∅ x 9tooth spin) |
312-1000-200 |
| 23 |
CONTINENTAL SHAFT BRG. RETAINER |
312-0100-002 |
| 24 |
CONTINENTAL SHAFT BRG. RETAINER SNAP RING |
391-2685-011 |
| Not Shown |
PUMP & PIGGY BACK 31/31 S.E.C.LIP SEAL |
391-2883-058 |
| Not Shown |
SEAL RETAINER FOR 51/51& 31/51 PIGGY BACK PUMP S.E.C. |
391-2584-063 |
| Not Shown |
SEAL RETAINER 0 RING FOR PIGGY BACK PUMP S.E.C. |
391-2881-124 |
| Not Shown |
SEAL RETAINER 0 RING FOR PIGGY BACK PUMP S.E.C. |
391-2881-120 |
| Not Shown |
SEAL RETAINER FOR 76/51 & 76/31 PIGGY BACK PUMPS.E.C. |
391-2585-013 |
| Not Shown |
CASE DRAIN PLUG |
391-2282-056 |
| Not Shown |
SHAFT KEY FOR TYPE 12 SHAFT |
391-1781-075 |
| Not Shown |
SHAFT KEY FOR TYPE 43 & 67 SHAFT |
391-1781-021 |
| Not Shown |
SHAFT KEY FOR TYPE 30 & 66 SHAFT |
391-1781-025 |
| Not Shown |
SHAFT KEY FOR TYPE Spl.SHAFT |
391-1781-020 |
| Not Shown |
30130 PIGGY BACK CONNECTING SHAFT |
312-1133-002 |
| Not Shown |
50/30 PIGGY BACK CONNECTING SHAFT |
312-1133-003 |
| Not Shown |
75/30 PIGGY BACK CONNECTING SHAFT |
316-1133-003 |
| |
|
|
| P50/P51 |
|
| NO. |
DESCRIPTION |
GENERAL NO. |
| 1 |
SHAFT BRG.SNAP RING |
391-2686-065 |
| 2a |
BEARING SPACER & SEAL RETAINER FOR MOTORS |
391-3383-087 |
| 2b |
INPUT SHAFT BEARING |
391-0381-077 |
| 3 |
MOTOR SEAL RETAINER USED WITH SHAFT BEARING |
391-3383-020 |
| 4a |
PUMP LIP SEAL |
391-2883-103 |
| 4b |
MOTOR LP SEAL |
391-2883-115 |
| 4c |
PUMP LIP SEAL FOR CONTINENTIAL SHAFT ONLY |
391-2883-133 |
| 5a |
51 PAD PI .OT PUMP SHAFT END COVER TYPE 00 |
313-5017-201 |
| 5b |
51 4 BOLTB PILOT PUMP SHAFT END COVER TYPE 42 (4" or 101,6 mm pilot) |
313-5037-201 |
| 5c |
51 4 BOLT c PIL OT PUMP SHAFT END COVER TYPE 78 (5" or 127 mm pilot) |
313-5037-202 |
| 5d |
51 2 BOLTB PILOT PUMP SHAFT END COVER TYPE 97 (4" or 101.6 mm pilot) |
313-5027-201 |
| 5e |
51 2 BOLT C PIL OT PUMP SHAFT END COVER TYPE 98 (5" or 127 mm pilot) |
313-5027-202 |
| 5f |
51 2 BOLT B (TYPE 2) PILOT PUMP SHAFT END COVER TYPE 96 (4" or 101,6 mm pilot) |
313-5027-205 |
| 5g |
51 2 BOLT C (TYPE 2) PIL OT PUMP SHAFT END COvER TYPE 99 (5" or 127 mm pilot) |
313-5027-206 |
| 5h |
51/51 SHAFT END COVER FOR PIGGYBACK UNITS TYPE 91 |
313-5027-208 |
| 51 |
76/51 SHAFT END COVER FOR PIGGYBACK UNITS TYPE 92 |
313-5027-209 |
| 5j |
51 PAD PILOT MOTOR SHAFT END COVER TYPE 00 |
313-5017-401 |
| 5k |
51 4 BOLT B PL oT MOTOR SHAFT END COVER TYPE 42 (4" or 101.6 mm pilot) |
313-5037-401 |
| 5L |
51 4 BOLT C PILOT MOTOR SHAFT END COVER TYPE 78 (5" or 127 mm pilot) |
313-5037-402 |
| 5m |
51 2 BOLT B PILOT MOTOR SHAFT END COVER TYPE 97 (4" or 101,6 mm pilot) |
313-5027-401 |
| 5n |
51 2 BOLT C PILOT MOTOR SHAFT END COVER TYPE 98 (5" or 127 mm pilot) |
313-5027-402 |
| |
FOR MORE INFORMATION OR SPECIAL ORDER,PLEASE CONTACT US |
GENERAL NO. |
| 6a |
CHECK VALVE MOTOR |
391-3681-001 |
| 6b |
PRESSURE PLUG PUMP |
391-2286-004 |
| 7 |
RING SEAL |
391-2585-009 |
| 8 |
ROLLER BEARING (∅1.937" 0.D.) |
391-0381-059 |
| 9a |
PUMP THRUST PLATE |
391-2185-029 |
| 9b |
MOTOR THRUST PLATE |
391-2185-012 |
| 9c |
DRY VALVE THRUST PLATE |
391-2185-041 |
| 10 |
POCKET SEAL |
391-2882-050 |
| 11a |
SHAFT & GEAR 14 TOOTH SPLINE 1.228"maj. dia. TYPE7 |
313-29XX-250 |
| 11b |
SHAFT & GEAR 1.250* KEYED (5/16) YPE 11 |
313-29XX-750 |
| 11c |
SHAFT & GEAR SET 13 TOOTH SPLINE 0.858"maj dia TYPE 25 |
313-29XX-230 |
| 11d |
SHAFT & GEAR SET 0.9984" dia. KEYED (14" x3/8" x1 14) TYPE 43 |
313-29XX-740 |
| 11e |
SHAFT & GEAR 14 TOOTH SPLINE 1.228* ma]. dia. TYPE 53 TYPE 2 |
313-29XX-450 |
| 11f |
SHAFT & GEAR SET 13 TOOTH SPLINE 0.858* maj. dia TYPE 65 TYPE2 |
313-29XX-430 |
| 12 |
PUMP & MOTOR HOUSING GASKET |
391-2884-021 |
| 13 |
HOUSING DOWELL PIN |
391-2082-032 |
| 14 |
PUMP & MOTOR GEAR HOUSING |
313-82XX-100 |
| 15a |
51 MOTOR BEARING CARRIER BLANK |
313-7740-100 |
| 15b |
51 PUMP BEARING CARRIER WITH COMMON PASSAGE |
313-7723-100 |
| 16 |
CONNECTING SHAFT |
313-1133-001 |
| 17 |
GEAR SET ONLY |
313-28XX-000 |
| 18a |
51PUMP & MOTOR PORT END COVER |
313-3120-100 |
| 18b |
51 PUMP & MOTOR PORT END COVER SPECIAL LARGER PORTING |
313-3420-100 |
| 18c |
51 PIGGY BACK REAR PORT END COVER |
313-5027-212 |
| 19 |
FLAT WASHER (5/8*) |
391-3784-028 |
| 20 |
BOLTS/STUDS (518"-UNC) |
|
| 21 |
HEX NUT (5/8"-UNC) |
391-1451-076 |
| 22a |
CONTINENTAL SHAFT TYPE 11 (1.250" ∅ KEYED 5/16") |
313-1500-500 |
| 22b |
CONTINENTAL SHAFT TYPE 7 (1.250" ∅- 14 TOOTH SPLINE) |
313-1135-194 |
| 22c |
CONTINENTAL SHAFT TYPE 25 (0.875" ∅- 13 TOOTH SPLINE) |
313-1000-300 |
| 22d |
CONTINENTAL SHAFT TP 43(100" ∅x 1/4" x 3/8* x 11/4" key) |
313-1500-400 |
| 22e |
CONTINENTAL SHAFT TYPE 73 LONG (1 250" ∅ KEYED 5/16") |
313-1500-502 |
| 23 |
CONTINENTAL SHAFT BRG. RETAINER (MAY NOT BE REQUIRED) |
391-3381-046 |
| 24 |
CONTINENTAL SHAFT BRG. RETAINER SNAP RING (MAY NOT BE REQ) |
391-2685-040 |
| Not Shown |
SEAL RETAINER FOR 51/51 PIGGY BACK PUMP S.E.C. |
391-2584-063 |
| Not Shown |
SEAL RETAINER 0 RING FOR PIGGY BACK PUMP S.E.C. |
391-2881-124 |
| Not Shown |
SEAL RETAINER 0 RING FOR PIGGY BACK PUMP S.E.C. |
391-2881-120 |
| Not Shown |
SEAL RETAINER FOR 76/51 PIGGY BACK PUMP S.E.C. |
391-2585-013 |
| Not Shown |
CASE DRAIN PLUG |
391-2282-056 |
| Not Shown |
DRY VALVE SEAL RETAINER |
391-2584-050 |
| Not Shown |
PUMP UIP SEAL FOR PIGGY BACK S.E.C.&P.E.C. |
391-2883-058 |
| Not Shown |
SHAFT KEY FOR TYPE 73 SHAF |
391-1781-008 |
| Not Shown |
SHAFT KEY FOR TYPE 43 SHAFT |
391-1781-021 |
| Not Shown |
SHAFT KEY FOR TYPE 11 SHAFT |
391-1781-045 |
| Not Shown |
50/50 PIGGY BACK CONNECTING SHAFT |
313-1133-004 |
| Not Shown |
75/50 PIGGY BACK CONNECTING SHAFT |
313-1133-003 |
| |
|
|
| P75/P76 |
|
| NO. |
DESCRIPTION |
GENERAL NO. |
| 1 |
SHAFT BRG. SNAP RING |
391-2686-025 |
| 2a |
INPUT SHAFT BRG. |
391-0381-078 |
| 2b |
SPACER TO REPLACE SHAFT BEARING |
391-3383-018 |
| 3a |
SEAL RETAINER FOR PUMPS |
391-2584-082 |
| 3b |
SEAL RETAINER FOR MOTORS |
391-2584-051 |
| 4 |
SEAL RETAINER 0 RING |
391-2881-457 |
| 5a |
PUMP LIP SEAL |
391-2883-052 |
| 5b |
MOTOR LIP SEAL |
391-2883-094 |
| 6a |
76 4 BOLT B PILOT PUMP S.E.C. TYPE 42 (4" or 101,6 mm pilot) |
316-5037-201 |
| 6b |
76 4 BOLT C PILOT PUMP S.E.C. TYPE 78 (5" or 127 mm pilot) |
316-5037-202 |
| 6c |
76 4 BOLT D PILOT PUMP S.E.C. TYPE 80 (6" or 152,4 mm pilot) |
316-5037-203 |
| 6d |
76 2 BOLT C PILOT PUMP S.E.C. TYPE 98 (5" or 127 mm pilot) |
316-5027-202 |
| 6e |
76 4 BOLT B PILOT MOTOR S.E.C. TYPE 42 (4" or 101,6 mm pilot) |
316-5037-401 |
| 6f |
76 4 BOLT C PILOT MOTOR S.E.C.TYPE 78 (5" or 127 mm pilot) |
316-5037-402 |
| 6g |
76 4 BOLT D PILOT MOTOR S.E.C. TYPE 80 (6" or 152,4 mm pilot) |
316-5037-403 |
| 6h |
76 2 BOLT C PILOT MOTOR S.E.C. TYPE 98 (5" or 127 mm pilot) |
316-5027-402 |
| 7a |
CHECK VALVE MOTOR |
391-3681-001 |
| 7b |
PRESSURE PLUG PUMP |
391-2286-004 |
| 8 |
DOWEL PIN |
391-2082-033 |
| 9 |
RING SEAL |
391-2585-011 |
| 10 |
ROLLER BEARING (∅2.322" 0.D.) |
391-0381-060 |
| 11 |
POCKET SEAL |
391-2882-052 |
| 12a |
PUMP THRUST PLATE |
391-2185-026 |
| 12b |
MOTOR THRUST PLATE |
391-2185-020 |
| 12c |
DRY VALVE THRUST PLATE |
391-2185-072 |
| Not Shown |
DRY VALVE THRUST PLATE SEAL |
391-2885-040 |
| |
FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US |
GENERAL NO. |
| 13a |
SHAFT & GEAR 14 TOOTH SPLINE 1.228"maj.dia. TYPE 7 |
316-29XX-250 |
| 13b |
SHAFT & GEAR 1.250" KEYED (5/16") TYPE 11 |
316-29XX-750 |
| 14 |
PUMP & MOTOR HOL JSING GASKET |
391-2884-024 |
| 15 |
PUMP & MOTOR GEAR HOUSING |
316-82XX-100 |
| 16 |
CONNECTING SHAFT |
316-1133-001 |
| 17a |
76 MOTOR BEARING CARRIER BLANK |
316-7740-100 |
| 17b |
76 PUMP BEARING CARRIER WITH COMMON PASSAGE |
316-7723-100 |
| 18 |
GEAR SET ONLY |
316-28XX-000 |
| 19 |
76 PUMP & MOTOR PORT END COVER |
316-3120-100 |
| 20 |
FLAT WASHER (5/8") |
391-3784-028 |
| 21 |
BOLTS / STUDS (5/8"-UNC) |
|
| 22 |
HEX NUT (5/8"-UNC) |
391-1451-076 |
| 23a |
CONTINENTAL SHAFT 14 TOOTH SPLINE 1.228"maj.dia. TYPE 7 |
316-1135-148 |
| 23b |
CONTINENTAL SHAFT 1.250"KEYED (5/16") TYPE 11 |
316-1135-147 |
| 23c |
CONTINENTAL SHAFT 14 TOOTH SPLINE 1.228". Dia. TYPE 7 Long |
316-1500-502 |
| 23d |
CONTINENTAL SHAFT 1.250"KEYED (5/16") TYPE 11 Long |
316-1500-501 |
| 24 |
CONTINENTAL SHAFT BRG. RETAINER |
391-3381-039 |
| 25 |
CONTINENTAL SHAFT BRG. RETAINER SNAP RING |
391-2685-029 |
| Not Shown |
PIGGY BACK CONNECTING SHAFT |
316-1133-003 |
| Not Shown |
PUMP LIP SEAL FOR PIGGY BACKP.E.C. |
391-2883-103 |
| Not Shown |
76 PIGGYBACK REAR PORT END COVER |
316-5027-213 |
| Not Shown |
DRIVE KEY FOR TYPE 11 SHAFT |
391-1781-045 |
| Not Shown |
DRY VALVE ASSEMBLY 1/2" CONNECTION |
316-PMV-24 |
| Not Shown |
DRY VALVE ASSEMBLY 2" CONNECTION |
316-PMV-32 |
| |
|
|
| P315 |
|
| NO. |
DESCRIPTION |
GENERAL NO. |
| 1 |
SEAL RETAINER SNAP RING MOTOR ONLY |
391-2686-016 |
| 2 |
SHAFT BEARING ( USED IN TYPE* 9O S.E.C.) |
391-0381-105 |
| 3 |
SEAL RETAINER FOR MOTORS ONLY |
391-3384-313 |
| 4a |
PUMP LIP SEAL |
391-2883-151 |
| 4b |
MOTOR UIP SEAL |
391-2883-156 |
| 5a |
2 BOLT A PILOT PUMP S.E.C. WITHOUT BUSHING TYPE 93 (3 1/4" or 82,55 mm pilot) |
326-5029-204 |
| 5b |
2 BOLT A PILOT PUMP S.E.C. WITH BUSHING TYPE 93 (3 1/4" or 82,55 mm pilot) |
326-5129-204 |
| 5c |
2 BOLT B PILOT PUMP S.E.C. WITHOUT BUSHING TYPE 96 (4" or 101,6 mm pilot) |
326-5029-203 |
| 5d |
2 BOLT B PILOT PUMP S.E.C. WITH BUSHING TYPE 96 (4" or 101,6 mm pilot) |
326-5129-203 |
| 5e |
2 BOLT A PILOT MOTOR s.E.C. WITHOUT BUSHING TYPE 93 (3 14" or 82,55 mm pilot) |
326-5029-404 |
| 5f |
2 BOLT A PILOT MOTOR S.E.C. WITH BUSHING TYPE 93 (3 14" or 82.55 mm pilot) |
326-5129-404 |
| 5g |
2 BOLT B PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 96 (4" or 101,6 mm pilot) |
326-5029-403 |
| 5h |
2 BOLT B PILOT MOTOR S.E.C. WITH BUSHING TYPE 96 (4" or 101,6 mm pilot) |
326-5129-403 |
| 5i |
4 BOLT 72 X 100 mm/ 80mm PILOT WITHOUT BUSHING TYPE 90 |
326-5033-205 |
| 5j |
4 BOLT 72X 100 mm/ 80mm PILOT WITH BUSHING TYPE 90 |
326-5133-205 |
| 5k |
PAD MOUNT WITHOUT BUSHING TYPE 95 |
326--5016-202 |
| 5L |
PAD MOUNT WITH BUSHING TYPE 95 |
326-5116-202 |
| 5m |
2 BOLT APILOT SEC TYPE 89 W/ SNAP RING |
326-5029-426 |
| 6a |
CHECK VALVE MOTOR |
391-3681-001 |
| 6b |
PRESSURE PL UG PUMP (may not be required) |
391-2286-004 |
| 7 |
SHAFT BUSHING |
391-0482-195 |
| 8 |
PUMP BUNA SEAL |
391-2883-168 |
| 9 |
PUMP NYLON BACKUP SEAL |
391-2883-169 |
| Not Shown |
MOTOR NYLON BACKUP SEAL |
391-2881-995 |
| Not Shown |
MOTOR THRUST PLATE SIDE SEAL |
391-2881-997 |
| Not Shown |
MOTOR THRUST PLATE END SEAL |
391-2881-996 |
| 10a |
PUMP THRUST PLATE |
391-2185-063 |
| 10b |
MOTOR THRUST PLATE |
391-2185-070 |
| 11a |
SHAFT & GEAR SAE "A" 0.625" dia. KEYED TYPE 97 |
326-29XX-920 |
| 11b |
SHAFT & GEAR SAE " A"9TOOTH SPLINE 0.609"maj. dia. TYPE 96 |
326-29XX-420 |
| 11c |
SHAFT & GEAR SAE "B" 0.875"dia. KEYED TYPE 66 |
326-29XX-930 |
| 11d |
SHAFT & GEAR SAE"B" 13-TOOTH SPLINE 0.858* maj. dia. TYPE 65 |
326-29XX-430 |
| 11e |
SHAFT & GEAR TAPERED M12 X 1.5 THD & 3X5 KEYED TYPE 60 |
326-290X-701 |
| 11f |
SHAFT & GEAR TAPERED 5/16 INTERNAL THD # WDF KEY TYPE 56 |
32629XX-604 |
| |
FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US |
GENERAL NO. |
| 12a |
PUMP HOUSING GASKET |
391-2881-968 |
| 12b |
MOTOR HOUSING GASKET |
391-2881-429 |
| 13 |
HOUSING DOWELL PIN |
391-2082-071 |
| 14a |
PUMP GEAR HOUSING |
326-81XX-100 |
| 14b |
MOTOR GEAR HOUSING |
326-82XX-100 |
| 15a |
315 BEARING CARRIER 1 OUTLET WITHOUT BUSHING |
326-7100-100 |
| 15b |
315 BEARING CARRIER 1 OUTLET WITH BUSHING |
326-7600-100 |
| 15c |
315 BEARING CARRIER 2 OUTLET WITHOUT BUSHING |
326-7300-100 |
| 15d |
315 BEARING CARRIER 2 OUTLET WITH BUSHING |
326-7800-100 |
| 16 |
CONNECTING SHAFT |
326-1133-001 |
| 17 |
GEAR SET ONLY |
326-28XX-000 |
| 18a |
315 PUMP P.E.C. NO PORTING WITHOUT BUSHING |
326-3000-100 |
| 18b |
315 PUMP P.E.C. NO PORTING WITH BUSHING |
326-3100-100 |
| 18c |
315 PUMP P.E.C. SIDE PORTING TYPE WITHOUT BUSHING |
326-3030-100 |
| 18d |
315 PUMP P.E.C. SIDE PORTING TYPE WITH BUSHING |
326-3130-100 |
| 18e |
315 PUMP P.E.C. SIDE & REAR PORTING TYPE WITHOUT BUSHING |
326-3133-100 |
| 18f |
315 PUMP P.E.C. SIDE & REAR PORTING TYPE WITH BUSHING |
326-3033-100 |
| 18g |
315 MOTOR P.E.C. PORTING TYPE WITHOUT BUSHING |
326-3020-100 |
| 18h |
315 MOTOR P.E.C. PORTING TYPE WITH BUSHING |
326-3120-100 |
| 19 |
BOLTS STUDS (12"-UNC) |
|
| 20 |
FLAT WASHER (1/2") |
391-3782-132 |
| 21 |
HEX NUT (1/2"-UNC) |
391-1451-051 |
| |
|
|
| P330 |
|
| NO. |
DESCRIPTION |
GENERAL NO. |
| 1 |
SHAFT BRG. SNAP RING |
391-2686-063 |
| 2a |
INPUT SHAFT BRG. |
391-0381-040 |
| 2b |
SPACER IN PLACE OF SHAFT BEARING |
391-3383-069 |
| 3 |
SEAL RETAINER FOR MOTORS ONLY |
391-3381-040 |
| 4a |
PUMP UP SEAL |
391-2883-058 |
| 4b |
MOTOR UIP SEAL |
391-2883-119 |
| 4c |
PUMP UP SEAL FOR CONTINENTAL SHAFT ONLY |
391-2883-107 |
| 4d |
MOTOR UP SEAL FOR CONTINENTAL SHAFT ONLY |
391-2883-126 |
| 5a |
4 BOLT B PiL OT PL JMP S.E.C. WITHOUT BUSHING TYPE 42 (4" or 101,6 mm pilot) |
324-5033-201 |
| 5b |
4 BOLT B PILOT PUMP S.E.C. WiITH BUSHING TYPE 42 (4" ar 101.6 mm pilot) |
324-5133-201 |
| 5c |
4 BOLT C PILOT PUMP S.E.C. WITHOUT BUSHING TYPE 78 (5" or 127 mm pilot) |
324-5033-202 |
| 5d |
4 BOLT C PIL .OT PUMP S.E.C. WITH BUSHING TYPE 78 (5" or 127 mm pilot) |
324-5133-202 |
| 5e |
2 BOLT B PILOT PUMP S.E.C. WITHOUT BUSHING TYPE 97 (4" or 101,6 mm pilot) |
324-5023-201 |
| 5f |
2 BOLT B PILOT PUMP S.E.C. WITH BUSHING TYPE 97 (4" or 101,6 mm pilot) |
324-5123-201 |
| 5g |
2&4 BOLT B PILOT PUMPS.E.C. WITHOUT BUSHING TYPE 46 (4 or 101.6 mm pilot) |
324-5053-201 |
| 5h |
2&4 BOLT B PILOT PUMP S.E.C. WITH BUSHING TYPE 46 (4 or 101,6 mm pilot) |
324-5153-201 |
| 5i |
4 BOLT B PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 42 (4" or 101,6 mm pilot) |
324-5033-401 |
| 5j |
4 BOLT B PILOT MOTOR S.E.C. WITH BUSHING TYPE 42 (4" or 101,6 mm pilot) |
324-5133-401 |
| 5k |
4 BOLT C PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 78 (5" or 127 mm pilot) |
324-5033-402 |
| 5L |
4 BOLT C PILOT MOTOR S.E.C. WITH BUSHING TYPE 78 (5" or 127 mm pilot) |
324-5133-402 |
| 5m |
2 BOLT B PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 97 (4" or 101,6 mm pilot) |
324-5023-401 |
| 5n |
2 BOLT B PILOT MOTOR S.E.C. WITH BUSHING TYPE 97 (4" or 101,6 mm pilot) |
324-5123-401 |
| 5o |
2 &4 BOLT B PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 46 (4" or 101,6 mm pilot) |
324-5053-401 |
| 5p |
2& 4 BOLT B PIL OT MOTOR S.E.C. WITH BUSHING TYPE 46 (4" or 101 6 mm pilot) |
324-5153-401 |
| |
FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US |
GENERAL NO. |
| 6a |
CHECK VALVE MOTOR |
391-3681-001 |
| 6b |
PRESSL JRE PLUG P MP (may mot be required) |
391-2286-004 |
| 7 |
SHAFT BUSHING |
391-0482-306 |
| 8 |
PUMP BUNA SEAL |
391-2883-166 |
| 9 |
PUMP NYLON BACKUP SEAL |
391-2883-167 |
| Not Shown |
MOTOR NYLON BACKUP SEAL |
391-2881-929 |
| Not Shown |
MOTOR THRUST PLATE SIDE SEAL |
391-2881-931 |
| Not Shown |
MOTOR THRUST PLATE END SEAL |
391-2881-930 |
| 10a |
PUMP THRUST PLATE |
391-2185-056 |
| 10b |
MOTOR THRUST PLATE |
391-2185-065 |
| 11a |
SHAFT & GEAR SET 13 TOOTH SPLINE 0.858"ma. dla TYPE 25 |
324-29XX-230 |
| 11b |
SHAFT & GEAR SET 0.9984* dia. KEYED (1/4" x3/8"x1 1/4") TYPE 43 |
324-29XX-740 |
| 11c |
SHAFT & GEAR SET 15 TOOTH SPL INE 0.983* maj. dia TYPE 98 |
324-29XX-240 |
| 12a |
PUMP HOUSING GASKET |
391-2884-050 |
| 12b |
MOTOR HOUSING GASKET |
391-2884-076 |
| 13 |
HOUSING DOWELL PIN |
391-2082-032 |
| 14a |
PUMP GEAR HOUSING |
324-81XX-100 |
| 14b |
MOTOR GEAR HOUSING |
324-82XX-100 |
| 15a |
330 BEARING CARRIER BLANK WITHOUT BUSHING |
324-7200-100 |
| 15b |
330 BEARING CARRIER BLANK WITH BUSHING |
324-7700-100 |
| 15c |
330 BEARING CARRIER 1 OUTLET WITHOUT BUSHING |
324-7100-100 |
| 15d |
330 BEARING CARRIER 1 OUTLET WITH BUSHING |
324-7600-100 |
| 15e |
330 BEARING CARRIER 2 OUTL ET WITHOUT BUSHING |
324-7300-100 |
| 15f |
330 BEARING CARRIER 2 OUTLET WITH BUSHING |
324-7800-100 |
| 15g |
330/315 BEARING CARRIER CW WITHOUT BUSHING |
324-3050-100 |
| 15h |
330/315 BEARING CARRIER CW WITH BUSHING |
324-3150-100 |
| 151 |
330/315 BEARING CARRIER CCW WITHOUT BUSHING |
324-3060-100 |
| 15j |
330/315 BEARING CARRIER CCW WITH BUSHING |
324-3160-100 |
| 16a |
CONNECTING SHAFT |
324-1133-001 |
| 16b |
PIGGYBACK CONNECTING SHAFT PHASE 2 |
324-1133-004 |
| 17 |
GEAR SET ONLY |
324-28XX-000 |
| 18a |
330 PUMP P.E.C. NO PORTING WITHOUT BUSHING |
324-3000-100 |
| 18b |
330 PUMP P.E.C. NO PORTING WITH BUSHING |
324-3100-100 |
| 18c |
330 P.E.C. NO PORTING WITHOUT BUSHING CHECK VALVE REQ. |
324-3000-101 |
| 18d |
330 P.E.C. NO PORTING WITH BUSHING CHECK VALVE REQ. |
324-3100-101 |
| 18e |
330 PUMPP.E.C. PORTING TYPE WITHOUT BUSHING |
324-3010-100 |
| 18f |
330 PUMPP.E.C. PORTING TYPE WITH BUSHING |
324-3110-100 |
| 18g |
330 MOTOR P.E.C. PORTING TYPE WITHOUT BUSHING |
324-3020-100 |
| 18h |
330 MOTOR P.E.C. PORTING TYPE WITH BUSHING |
324-3120-100 |
| 19 |
BOLTS/STUDS (5/8"-UNC) |
|
| 20 |
FLAT WASHER (5/8") |
391-3784-028 |
| 21 |
HEX NUT (5/8"-UNC) |
391-1451-076 |
| Not Shown |
CONTINENTAL SHAFT 14 TOOTH SPLINE 1.223"maj. dia. TYPE 7 |
324-1000-500 |
| Not Shown |
CONTINENTAL SHAFT 13 TOOTH SPLINE 0.858"maj. dia. TYPE 25 |
324-1000-300 |
| Not Shown |
CONTINENTAL SHAFT 0.9984 dia. KEYED (1/4"x 318" x1 1/4") TYPE 43 |
324-1500-400 |
| Not Shown |
CONTINENTAL SHAFT 15 TOOTH SPLINE 0.983" maj. dia. TYPE 98 |
324-1200-400 |
| Not Shown |
CONTINENTAL SHAFT 0.875" dia. KEYED (1/4" x 3/8" x 1") TYPE 30 |
324-1500-300 |
| Not Shown |
DRIVE KEY FOR TYPE 43 SHAFT |
391-1781-082 |
| Not Shown |
DRIVE KEY FOR TYPE 30 SHAFT |
391-1781-085 |
| Not Shown |
CONTINENTAL SHAFT BRG. RETAINER |
312-0100-002 |
| Not Shown |
CONTINENTAL SHAFT BRG. RETAINER SNAP RING |
391-2685-011 |
| |
|
|
| P350 |
|
| NO. |
DESCRIPTION |
GENERAL NO. |
| 1 |
SHAFT BRG. SNAP RING |
391-2686-065 |
| 2a |
INPUT SHAFT BRG. |
391-0381-077 |
| 2b |
SEAL RETAINER & SPACER N Pu ACE OF SHAFT BRG. |
391-3383-087 |
| 3 |
SEAL RETAINER FOR MOTORS ONLY |
391-3383-020 |
| 4a |
PUMP LIP SEAL |
391-2883-103 |
| 4b |
MOTOR UP SEAL |
391-2883-115 |
| 4c |
SEAL FOR CONTINENTAL SHAFT |
391-2883-133 |
| 5a |
4 BOLT B Moi iNT PUMP s E c. WITHOUT BUSHING TYPE 42 4 or 101.6 mm pilot) |
323-5033-201 |
| 5b |
4 BOLT B MOUNT PUMP s.E.C. WITH BUSHING TYPE 42 (4 or 101,6 mm pilot) |
323-5133-201 |
| 5c |
2/4 BOLT B MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 46 (4 or 101.6 mm pilot) |
323-5053-201 |
| 5a |
2/4 BOLT B MOUNT PUMP S.E c. WiTH BUSHING TYPE 46 (4" or 101.6 mm pilot) |
323-5153-201 |
| 5e |
4 BOLT C MOUNT PUMP S.E.C. WTTHOUT BUSHING TYPE 78 5 r 127 mm pilot) |
323-5033-202 |
| 5f |
4 BOLT C MOUNT PUMP s.E C wimH BUSHING TYPE 78 (5" or 127 mm pilot) |
323-5133-202 |
| 5g |
2 BOLT MOUNT PUMP S.EC. WTTHOUT BUSHING TYPE 97 4 or 101.6 mpilco |
323-5023-201 |
| 5h |
2 BOLT B MOUNT PUMP s.E.C. WITH BUSHING TYPE 97 (4 or 101.6 mm pilot) |
323-5123-201 |
| 5i |
2 BOLT C MOUNT PUMP s.E C WITHOUT BUSHING TYPE 9B 5 or 127 mm pilot) |
323-5023-202 |
| 5j |
2 BOLT C MOUNT PUMP s. E C. wWiTH BUSHING TYPE 98 (5 or 127 mm pilot) |
323-5123-202 |
| 5k |
4 BOLT B MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 42 (4 or 101.6 mm pilot) |
323-5033-401 |
| 5L |
4 BOLT B MOUNT MOTOR S.E.C. WTH BUSHING TYPE 42 (4" or 101.6 mm pilot) |
323-5133-401 |
| 5m |
2/4 BOLT B MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 46 (4* or 101.6 mm pilot) |
323-5053-401 |
| 5n |
2/4 BOLT B MOUNT MOTOR s.E.C. WITH BUSHING TYPE 46 4 cr 101.6 mm pilot) |
323-5153-401 |
| 5o |
4 BOLT C MOUNT MOTOR s.E. c. WITHOUT BUSHING TYPE 78 (5 or 127 mm pilot) |
323-5033-402 |
| 5p |
4 BOLT C MOUNT MOTOR s.E. c. WITH BUSHING TYPE 78 (5 or 127 mm pilot) |
323-5133-402 |
| 5q |
2 BOLT B MOUNT MOTOR s.E.C. WTHOUT BUSHING TYPE 97 (4 or 101.6 mm pilot) |
323-5023-401 |
| 5r |
2 BOLT B MOUNT MOTOR S.E.C. WTH BUSHING TYPE 97 (4" or 101.6 mm pilot) |
323-5123-401 |
| 5s |
2 BOLT C MOUNT MOTOR s.E.C. WITHOUT BUSHING TYPE 98 (5 or 127 mm pilot) |
323-5023-402 |
| 5t |
2 BOLT C MOUNT MOTOR S.E.C. WITH BUSHING TYPE 98 (5 or 127 mm pilot ) |
323-5123-402 |
| |
FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US |
GENERAL NO. |
| 6a |
CHECK VALVE MOTOR |
391-3681-001 |
| 6b |
PRESSURE PLUG PUMP |
391-2286-004 |
| 7 |
SHAFT BUSHING |
391-0482-308 |
| 8 |
PUMP BUNA SEAL |
391-2883-140 |
| 9 |
PUMP NYL ON BACKUP SEAL |
391-2883-139 |
| 10a |
PUMP THRUST PLATE |
391-2185-057 |
| 10 b |
MOTOR THRUST PLATE |
391-2185-068 |
| Not shown |
MOTOR NYLON BACKUP SEAL |
391-2885-075 |
| Not shown |
MOTOR THRUST PL ATE SIDE SEAL |
391-2885-073 |
| Not Shown |
MOTOR THRUST PL ATE END SEAL |
391-2885-074 |
| 11a |
SHAFT & GEAR 14 TOOTH SPUINE 1.228" maj. da. TYPE 7 |
323-29XX-250 |
| 11b |
SHAFT & GEAR 1.250* KEYED (5/16") TYPE 11 |
323-29XX-750 |
| 11c |
SHAFT & GEAR sET 13 TOOTH SPUNE 0.858"- maj. dia TYPE 25 |
323-29XX-230 |
| 11d |
SHAFT & GEAR sET 0 9984 da. KEYED (1/4"'x3/8"x1 1/4") TYPE 43 |
323-29XX-740 |
| 11e |
SHAFT & GEAR 15 TOOTH SPINE 0.980" maj dia. TYPE 98 |
323-29XX-240 |
| 11f |
SHAFT & GEAR 1.250* dia. KEYED (5/16" X 5/16" x2 1/4") TYPE 73 |
323-29XX-752 |
| 12a |
PUMP HOUSING GASKET |
391-2884-074 |
| 12b |
MOTOR HOUSING GASKET |
391-2884-021 |
| 13 |
HOUSING DOWELL PIN |
391-2082-032 |
| 14a |
PUMP GEAR HOUSING |
323-81XX-100 |
| 14b |
MOTOR GEAR HOUSING |
323-82XX-100 |
| 15a |
350 BEARING CARRIER B ANK WITHOUT BUSHING |
323-7200-100 |
| 15b |
350 BEARING CARRIER BLANK WITH BUSHING |
323-7700-100 |
| 15c |
350 BEARING CARRIER 1 OUTLET WITHOUT BUSHING |
323-7100-100 |
| 15d |
350 BEARING CARRIER 1 OUTLET WITH BUSHING |
323-7600-100 |
| 15e |
350 BEARING CARRIER 2 OUTLET WITHOUT BUSHING |
323-7300-100 |
| 15f |
350 BEARING CARRIER 2 OUTLET WITH BUSHING |
323-7800-100 |
| 15g |
350/315 BEARING CARRIER CW WITHOUT BUSHING |
323-3050-100 |
| 15h |
350/315 BEARING CARRIER Cw WITH BUSHING |
323-3150-100 |
| 151 |
350/315 BEARING CARRIER ccW WITHOUT BUSHING |
323-3060-100 |
| 15j |
350/315 BEARING CARRIER ccw WITH BUSHING |
323-3160-100 |
| 16a |
CONNECTING SHAFT |
323-1133-001 |
| 16b |
PIGGYBACK CONNECTING SHAFT PHASE 2 |
323-1133-006 |
| 16c |
PIGGY BACK CONNECTING SHAFT BEARING SNAP RING |
391-2686-019 |
| 16d |
PIGGY BACK CONNECTING SHAFT BEARING |
391-0381-099 |
| 160 |
PIGGY BACK CONNECTING SHAFT SAE "B" SPUNE |
323-1133-003 |
| 16f |
PIGGY BACK CONNECTING SHAFT SAE "A" SPUINE |
323-1133-002 |
| 17 |
GEAR SET ONLY |
323-28XX-000 |
| 18a |
350 PUMP & MOTOR P.E C. WITHOUT BUSHING NO PORTING |
323-3000-100 |
| 18b |
350 PUMP & MOTOR P.E.C. WITH BUSHING NO PORTING |
323-3100-100 |
| 18c |
350 PUMP P.E.C. PORTING TYPE WITHOUT BUSHING |
323-3010-100 |
| 18d |
350 PUMP P.E.C. PORTING TYPE WITH BUSHING |
323-3110-100 |
| 18g |
350 MOTOR P.E.C. PORTING TYPE WITHOUT BUSHING |
323-3020-100 |
| 18f |
350 MOTOR P.EC. PORTING TYPE WITH BUsHING |
323-3120-100 |
| 18g |
350 P.E.C. TO S.A.E. "A" PILOT CW WITHOUT BUSHING |
323-3054-099 |
| 18h |
350 P.E.C. TO S.A.E. "A" PLOT CW wimH BUSHING |
323-3154-099 |
| 181 |
350 P.E.C. TO S.A.E. "A" PILOT CCW WITHOUT BUSsHING |
323-3064-099 |
| 18j |
350 P.E.C. TO S.A.E. "A" PILOT CCW WITH BUSHING |
323-3164-099 |
| 18k |
350 P.E.C. TO S.A.E. "B" PILOT CW WITHOUT BUSHING |
323-3054-100 |
| 18L |
350 P.E.C. TO S.A.E. "B" PILOT CW WITH BUSHING |
323-3154-100 |
| 18m |
350 P.E.C. TO S.A.E. "B" PILOT CCW WITHOUT BUSHING |
323-3064-100 |
| 18n |
350 P.E.C. TO S.A.E. "B" PILOT CCW WITH BUSHING |
323-3164-100 |
| 19 |
BOLTS1 STUDS (5/8"-UNC) |
|
| 20 |
FLATWASHER (5/8") |
391-3784-028 |
| 21 |
HEX NUT (5/8"-UNC) |
391-1451-076 |
| Not Shown |
CONTINENTAL SHAF 1 250 KEYED (5/16") TYPE 11 |
323-1500-500 |
| Not Shown |
CONTINENTAL SHAFT TYPE 25 (0.875"∅- 13TOOTH SPLINE) |
323-1000-300 |
| Not Shown |
CONTINENTAL SHAFT TYPE 73 LONG (1 1/4"∅ KEYED 5/16") |
323-1500-502 |
| Not Shown |
CONTINENTAL SHAFT14 TOOTH SPUN 228" ma..TYPE 7 |
323-1135-194 |
| Not Shown |
CONTINENTAL SHAF TYE431(10000 14 x 318*x1 14 key) |
323-1500-400 |
| Not Shown |
DRIVE KEY FOR TYPE 11 SHAFT |
391-1781-083 |
| Not shown |
DRIVE KEY FOR TYPE 43 SHAFT |
391-1781-082 |
| Not Shown |
DRVE KEY FOR TYPE 73 SHAFT |
391-1781-088 |
| Not Shown |
CONTINENTAL SHAFT BRG. RETAINER |
391-3381-046 |
| Not Shown |
CONTINENTAL SHAFT BRG. RETAINER SNAP RING |
391-2685-040 |
| Not Shown |
CASE DRAIN PLUG |
391-2281-010 |
| |
|
|
| P365 |
|
| NO. |
DESCRIPTION |
GENERAL NO. |
| 1 |
SHAFT BRG. SNAP RING |
391-2688-025 |
| 2a |
INPUT SHAF BRG. |
391-0381-078 |
| 2b |
SEAL RETAINER & SPACER IN PLACE OF SHAFT BRG. |
391-3383-099 |
| 3 |
SEAL RETAINER FOR MOTORS ONLY |
391-2584-119 |
| 4a |
PUMP UP SEAL |
391-2883-052 |
| 4b |
MOTOR LP SEAL |
391-2883-094 |
| 5a |
4 BOLT B MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 42 (4" or 101,6 mm pilot) |
322-5033-201 |
| 5b |
4 BOLT B MOUNT PUMP S.E.C. WITH BUSHING TYPE 42 (4" or 101.6 mm pilot) |
322-5133-201 |
| 5c |
4 BOLT C MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 78 (5" or 127 mm pilot) |
322-5033-202 |
| 5d |
4 BOLT C MOLNT PUMP S.E.C. WITH BUSHING TYPE 78(5or127 mm pilot) |
322-5133-202 |
| 5e |
2 BOLT B MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 97 (4" or 101.6 mm pilot) |
322-5023-201 |
| 5f |
2 BOLT B MOUNT PUMP S.E.C. WITH BUSHING TYPE 97 (4" or 101.6 mm pilot) |
322-5123-201 |
| 5g |
2 BOLT C MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 98 (5" or 127 mm pilot) |
322-5023-202 |
| 5h |
2 BOLT C MOUNT PUMP S.E.C. WITH BUSHING TYPE 99 (5" or 127 mm pilot) |
322-5123-202 |
| 5i |
4 BOLT B MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 42 (4" or 101,6 mm pilot) |
322-5033-401 |
| 5j |
4 BOLT B MOUNT MOTOR S.E.C. WITH BUSHING TYPE 42 (4" or 101.6 mm pilot) |
322-5133-401 |
| 5k |
4 BOLT C MOUNT MOTOR S.E.C. WTHOuT BUSHING TYPE 78 (5" or 127 mm pilot) |
322-5033-402 |
| 5L |
4 BOLT C MOUNT MOTOR S.E.C. WITH BUSHING TYPE 78 (5" or 127 mm pilot) |
322-5133-402 |
| 5m |
2 BOLT B MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 97 (4" or 101,6 mm pilot) |
322-5023-401 |
| 5n |
2 BOLT B MOUNT MOTOR S.E.C. WITH BUSHING TYPE 97 (4" or 101.6 mm pilot) |
322-5123-401 |
| 5o |
2 BOLT C MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 98 (5" or 127 mm pilot) |
322-5023-402 |
| 5p |
2 BOLT C MOUNT MOTOR S.E.C. WITH BUSHING TYPE 98 (5" or 127 mm pilot) |
322-5123-402 |
| 6a |
CHECK VALVE MOTOR ( Not nequirnd on a moders ) |
391-3081-001 |
| 6b |
PRESSURE PLUG PUMP ( Nat requlred on all models ) |
391-2286-004 |
| 7 |
SHAFT BUSHING |
391-0482-307 |
| 8 |
PUMP BUNA SEAL |
391-2883-176 |
| 9 |
PUMP NYLON BACKUP SEAL |
391-2883-177 |
| Not Shown |
MOTOR NYLON BACKUP SEAL |
391-2885-071 |
| Not Shown |
MOTOR THRUST PLATE SIDE SEAL |
391-2885-069 |
| Not Shown |
MOTOR THRUST PLATE END SEAL |
391-2885-070 |
| 10a |
PUMP THRUST PLATE |
391-2185-055 |
| 10b |
MOTOR THRUST PLATE |
391-2185-060 |
| |
FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US |
GENERAL NO. |
| 11a |
SHAFT & GEAR 14 TOOTH SPLINE 1.228" maj. dia TYPE 7 |
322-29XX-250 |
| 11b |
SHAFT & GEAR 1 250" KEYED (5/16") TYPE 11 |
322-29XX-750 |
| 11c |
SHAF & GEAR SE 13 TOOTH SPUNE 0.858"maj. dia TYPE 25 |
322-29XX-230 |
| 12a |
PUMP HOUSING GASKET |
391-2884-052 |
| 12b |
MOTOR HOUSING GASKET |
391-2884-023 |
| 13a |
PUMP HOUSING DOWELL PIN |
391-2082-062 |
| 13b |
MOTOR HOUSING DOWELL PIN |
391-2082-069 |
| 14a |
PUMP GEAR HOUSING |
322-81XX-100 |
| 14b |
MOTOR GEAR HOUSING |
322-82XX-100 |
| 15a |
365 BEARING CARRIER 1 OUTLET WITHOUT BUSHING |
322-7100-100 |
| 15b |
365 BEARING CARRIER 1 OUTLET WITH BUSHING |
322-7600-100 |
| 15c |
365 BEARING CARRIER 2 OUTLET WITHOUT BUSHING |
322-7300-100 |
| 15d |
365 BEARING CARRIER 2 OUTLET WITH BUSHING |
322-7800-100 |
| 15e |
365 MOTOR BEARING CARRIER BLANK WTHOUT BUSHING |
322-7200-100 |
| 151 |
365 MOTOR BEARING CARRIER BLANK WITH BUSHING |
322-7700-100 |
| 15g |
365/330 BEARING CARRIER CW WITHOUT BUSHING |
322-3050-100 |
| 15h |
365/330 BEARING CARRIER CW WITH BUSHING |
322-3150-100 |
| 15i |
365/330 BEARING CARRIER CCW WITHOUT BUSHING |
322-3060-100 |
| 15j |
365/330 BEARING CARRIER CCW WITH BUSHING |
322-3160-100 |
| 16a |
CONNECTING SHAFT |
322-1133-001 |
| 16b |
PIGGYBACK CONNECTING SHAFT 365/330 |
322-1133-002 |
| 17 |
GEAR SET ONLY |
322-28XX-000 |
| 18a |
365 PUMP PORT END COVER WITHOUT BUSHING NO PORTING |
322-3000-100 |
| 18b |
365 PUMP PORT END COVER WITH BUSHING NO PORTING |
322-3100-100 |
| 18c |
365 PUMP PORT END COVER WITHOUT BUSHING PORTING TYPE |
322-3010-100 |
| 18d |
365 PUMP PORT END COVER WITH BUSHING PORTING TYPE |
322-3110-100 |
| 18e |
365 MOTOR PORT END COVER WITHOUT BUSHING NO PORTING |
322-3000-099 |
| 18f |
365 MOTOR PORT END COVER WITH BUSHING NO PORTING |
322-3100-099 |
| 18g |
365 MOTOR PORT END COVER WITHOUT BUSHING PORTING TYPE |
322-3020-100 |
| 18h |
365 MOTOR PORT END COVER WITH BUSHING PORTING TYPE |
322-3120-100 |
| 18i |
365 P.E.C. TO S.A.E. "A" PILOT CW WITHOUT BUSHING |
322-3054-099 |
| 18j |
365 P.E.C. TO S.AE. "A" PILOT CW WITH BUSHING |
322-3154-099 |
| 18k |
385 P.E.C. TO S,AE. "A" PILOT CCW WITHOUT BUSHING |
322-3064-099 |
| 18L |
365 P.E.C. TO S.AE. "A" PILOT CCW WiTH BUSHING |
322-3164099 |
| 18m |
365 P.E.C. TO S.AE. "A" PILOT CW WITHOUT BUSHING |
322-3054-100 |
| 18n |
365 P.E.C. TO S.AE. "B" PILOT CW WITH BUSHING |
322-3154-100 |
| 180 |
365 P.E.C.TOS.A.E. "B" PILOT CCW WITHOUT BUSHING |
322-3064-100 |
| 18p |
365 P.E.C.TOS.A.E. "B" PILOT CCW WITH BUSHING |
322-3164-100 |
| 19 |
BOLTS/STUDS |
|
| 20a |
MOTOR FLAT WASHER |
391-3782-114 |
| 20b |
PUMP FLAT WASHER |
391-3784-028 |
| 21a |
PUMP HEX NUT |
391-1451-076 |
| 21b |
MOTOR HEX NUT |
391-1451-088 |
| Not Shown |
CONTINENTAL SHAFT 1.250"KEYED (5/16") TYPE 11 |
322-1500-500 |
| Not Shown |
CONTINENTAL SHAFT 14 TOOTH SPL INE 1.228" ma. dia.TYPE 7 |
322-1000-500 |
| Not Shown |
CONTINENTALL SHAFT BRG. RETAINER |
391-3782-158 |
| Not Shown |
CONTINENTAL SHAFT BRG. RETAINER SNAP RING |
391-2685-029 |
| Not Shown |
SHAFT KEY FOR TYPE 11 SHAFT |
391-1781-083 |
| Not Shown |
PIGGYBACK CONNECTING SHAFT BEARING |
391-0381-099 |
| Not Shown |
PIGGYBACK CONNECTING SHAFTUP SEAL |
391-2883-103 |
| Not Shown |
PIGGYBACK CONNECTING SHAFT BEARING SNAP RING |
391-2686-019 |
| Not Shown |
1/4" ORB DRAIN PLUG |
391-2281-010 |
){kind=link}